Why a sliding ruler throws off your cut
A ruler that shifts while you press down on a rotary cutter turns a straight strip into a wavy one, and the error multiplies with every subsequent cut. Before you blame your blade or your technique, look at the contact between ruler and fabric. Most rulers are smooth on both faces, so they slide easily across cotton until you add something that grabs.
Dritz Quilter's Slip N Grips are designed for exactly that job: they are pressure-sensitive fabric grabbers that you apply to a ruler or template. The key word is pressure-sensitive. The ruler still slips across the fabric when you want to reposition it, and it grips when you press down to cut or mark.
What Slip N Grips actually do
- Quilters Slip N Grips, 32 pc: Dritz Quilter's Slip N Grips are pressure sensitive fabric grabbers that can be easily applied to a ruler or template. They are not a permanent non-slip coating. You stick them on yourself, so placement is under your control.

Quilters Slip N Grips, 32 pc - Quilters Slip N Grips, 32 pc: With Slip N Grips a ruler can be slipped across fabric and will grip when pressure is applied. This is the behavior that solves slipping without making the ruler hard to move between cuts.
- Quilters Slip N Grips, 32 pc: These self stick fabric grabbers make cutting and marking easier and more accurate. The benefit applies to both rotary cutting and marking, so one pack can serve more than one step in your workflow.
How to apply Slip N Grips to a ruler
The supplied product details confirm that the grips are pressure-sensitive and self-stick, and that they can be applied to a ruler or template. They do not specify a required number of grips, a spacing pattern, or a cure time, so the steps below are a practical starting point rather than a manufacturer procedure. Test on a scrap before committing to a layout.
- Clean and dry the ruler face: Wipe the underside of the ruler so the adhesive contacts a clean surface. Dust and lint reduce how well any self-stick item holds.
- Place grips where your hand presses: Put grips under the areas you press during a cut, not just at the corners. The grip activates on pressure, so it needs to sit where downward force is applied.
- Keep the measuring edge clear: Leave the edge you align with the fabric and blade free of grips so you can still read the markings and seat the ruler flush against the fabric edge.
- Test the slide-then-grip feel: Set the ruler on scrap fabric. It should still slide when you nudge it lightly and hold when you press down. If it drags too much, reposition the grips rather than adding more.
Placement tips for cleaner cuts
Because the package contains 32 grips, you have enough to experiment and still outfit more than one ruler. These placement habits help you get the most from that quantity.
- Spread grips instead of clustering them: A few grips spread across the pressing area stabilize the ruler better than a tight cluster in one corner. The product record does not prescribe a count, so start sparse and add only if the ruler still shifts.
- Match placement to your cutting hand: If you press mainly near the middle of the ruler, put grips there. If you press near the far end, cover that end. The goal is grip where force is applied.
- Use them on templates too: The supplied details say the grips can be applied to a ruler or template, so marking templates can benefit from the same pressure-sensitive hold.
- Keep the backing handy for storage: The record does not describe reuse or reapplication, so treat the grips as self-stick items applied once. Store rulers so the grip faces are not crushed against other tools.
When grips help and when the problem is elsewhere
Slip N Grips address one specific cause of inaccurate cutting: a ruler that moves under pressure. If your ruler is already stable and cuts are still off, the issue may be blade condition, fabric shifting under the mat, or how you are holding the cutter. The supplied product information does not cover those causes, so this article does not prescribe fixes for them.
What the record does support is a simple test. Apply a few grips, press down as you would during a cut, and see whether the ruler holds. If it does, the grips are doing their job. If it still slides, add another grip in the pressing zone before assuming the product is at fault.
Package details worth knowing
- Quilters Slip N Grips, 32 pc: This package contains 32 Slip N Grips. Enough grips to outfit a ruler and a template, or to spread across several rulers in a shared sewing space.
- Quilters Slip N Grips, 32 pc: Item Number: 3141. Useful if you want to match the same Dritz item when restocking or buying a second pack.

